Try These Dell DNDNS-200 Exam Questions – Updated 2018

Free demo of Dell Certified Professional DNDNS-200 certification exam is available before the real DNDNS-200 exam purchase once you are sure about the DNDNS-200 exam purchase then make the payment and get the Dell Networking Professional DNDNS-200 exam dumps practice software instantly. PDF Questions and Answers booklet with the Dell DNDNS-200 exam practice software is also available with an attractive offer of 30% discount. The booklet and practice test software together facilitates you for learning and practice both in the best manner. The most updated Dell Networking Professional DNDNS-200 exam questions of Dell DNDNS-200 exam are provided in the PDF booklet.

♥ VALID DNDNS-200 Exam Questions 2018 ♥

DNDNS-200 exam questions, DNDNS-200 PDF dumps; DNDNS-200 exam dumps:: https://www.dumpsschool.com/DNDNS-200-exam-dumps.html (60 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest Dell DNDNS-200 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

A new switch is already configured with an IP address and is reachable within the network. SSH and HTTPS are verified. The network engineer needs to disable HTTP for switch management.
What is the correct command?

A. console# no ip https server
B. console(config)# no ip http server
C. console# no ip http server
D. console(config)#ip http server disable

Answer: B

Question: 22

In an OSPF network, a network engineer uses a loopback interface with an assigned IP Address instead of configuring an IPv4 address as the Router I.
What are two benefits of this choice? (Choose two.)

A. OSPF is more reliable when a loopback interface is configured because a loopback interface is always active.
B. The loopback interface does not require a different subnet to be configured on each switch.
C. Not using a loopback interface saves real IP address space that can be used in the future.
D. The loopback interface IP address when advertised via OSPF can be used as a reliable remote management IP address.

Answer: A,D

Question: 23

Refer to the exhibit.
A network engineer is called onsite to troubleshoot replication failure and traffic loss. Whenever replication occurs between SAN A and SAN B, users report traffic loss between sites, and replication ultimately fails due to traffic loss.
Based on the topology shown, what is the most likely cause of the traffic loss?

A. Traffic needs to be policed on the site border routers.
B. An inbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
C. An outbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
D. Traffic needs to be shaped on the site border routers.

Answer: C

Explanation:
In Quality of Service, DSCP value 46 is high-priority traffic.

Question: 24

Refer to the exhibit of the N-series switches.
The exhibit shows a Layer 2 network between Host A (a Desktop Computer running Windows 7) and Host B (another Desktop Computer running Windows 7) and the list of VLANs Untagged (U) and Tagged (T) at each Ethernet interface: Host A transmits an Ethernet frame untagged on VLAN 1.
What will happen to the Ethernet frame?

A. SW2 drops the Ethernet frame when trying to transmit it out of interface E2 because the incoming and outgoing interfaces are Tagging/Untagging VLAN 1 differently.
B. The Ethernet frame is successfully delivered to Host.
C. STP drops the Ethernet frame because it cannot create an end-to-end loop free path between the switches for VLAN 1.
D. VLAN consistency protocol determines that the VLAN is not correctly Tagged/Untagged on all interfaces, an error will occur, and SW1 will drop the frame on interface E2.

Answer: B

Question: 25

Refer to the exhibit.
Considering the network topology and information shown, what is an issue with end point devices in network 192.168.102.0/24 that try to route to 192.168.101.0/24?

A. ICMP Redirects
B. Suboptimal Routing
C. Routing Loop
D. Summarization Black Hole

Answer: C

Question: 26

Refer to the Exhibit.
A network engineer receives the output shown when removing MLAG from a pair of N-Series switches.
Which sequence of steps must the engineer complete to remove the vpc peer-link from Port Channel 1?

A. Shut down the Port Channel interfaceIssue the no vpc peer-link command on the Port Channel
B. Remove the vpc feature using the no feature vpc commandIssue the no vpc peer-link command on the Port Channel
C. Remove the channel-group command from all members of the Port ChannelIssue the no vpc peer-link command on the Port Channel
D. Remove peer-keepalive enable using the no peer-keepalive enable commandIssue the no vpc peer-link command on the Port Channel

Answer: D

New Updated DNDNS-200 Exam Questions DNDNS-200 PDF dumps DNDNS-200 practice exam dumps: https://www.dumpsschool.com/DNDNS-200-exam-dumps.html